When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. Be sure that the clamps are tight enough that the Cisco Wirelessĭo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. Tighten the band clamps with the wrench so that theĬisco Wireless Gateway for LoRaWAN does not slide on the pole. Locate the Cisco Wireless Gateway for LoRaWAN to its final position. Using a 10-mm wrench, tighten the four bolts that connect the Cisco Wireless Gateway for LoRaWAN to the bracket to a torque The Cisco Wireless Gateway for LoRaWAN must be positioned with the LEDs on the bottom to allow viewing from the ground. Check to be sure that theĬisco Wireless Gateway for LoRaWAN is properly seated in the slots. Position the four bolts on the Cisco Wireless Gateway for LoRaWAN into the bracket keyhole slots. Screw an M6 bolt into each of the four bolt holes on the back side of the Cisco Wireless Gateway for LoRaWAN. Only tighten them enough to keep the bracket from sliding down the pole. Wrap the band clamps around the pole and slide them into the second set of top and bottom mounting slots on the bracket. Cisco Wireless Gateway for LoRaWAN and Fixed Mount Kit Installed on a Pole Using a 10-mm wrench, secure the Cisco Wireless Gateway for LoRaWAN to the bracket by tightening the bolts to the bracket įigure 2. Slide the Cisco Wireless Gateway for LoRaWAN down to sit securely in the quick mount slots. Position the four bolts on the Cisco Wireless Gateway for LoRaWAN into the keyhole slots on the mounting bracket. Not screw the bolt all the way in leave approximately a 1/8” (3.3 mm) space. Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the Cisco Wireless Gateway for LoRaWAN. If necessary, use a suitable screw anchors and an exterior-grade plywood backboard to mount the Cisco Wireless Gateway for Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface. Mounting Slots (used with the band clamps)īracket Mount Holes (use bolts up to 1/4" or 6 mm in diameter) Quick Mount Keyhole Slots (for the Cisco LoRa Interface use) Otherwise, it may lead to water leaking into the Cisco Wireless Gateway for LoRaWAN. If the DC power port, LAN port, or the PoE-In port is not in use, the port’s covering plug must be tightened to 12.5 in-lbs If you do not tighten the plug properly, it will not meet IP67 criteria, and may lead to water leaking into the unit.įigure 1. Tighten it at the time of installation, and also every time the plug is removed and replaced. Inspect the seal of the plug and properly The Console-Reset port and the Reset button are under a hex-shaped sealed plug. Install the device in an area where structures, trees, or hills do not obstruct radio signals to and from the device. Perform a site survey before beginning the installation. Follow these basic guidelines to ensure the best possible performance: If an accident should occur, call for qualified emergency help immediately.īecause the Cisco Wireless Gateway for LoRaWAN is a radio device, it is susceptible to common causes of interference thatĬan reduce throughput and range. If any part of the antenna system should come in contact with a power line, do not touch it or try to remove it yourself.Ĭall your local power company. If the assembly starts to drop, get away from it and let it fall. When installing the access point and antennas, remember:ĭo dress properly-shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket. Should be in charge of the operation to issue instructions and watch for signs of trouble. Each person should be assigned to a specific task and should know what to do and when to do it. Successful raising of a mast or tower is largely a matter Plan your installation carefully and completely before you begin. Tell them your plans, and ask them to come look at your proposed installation. For safety, assume that any overhead line can kill.Ĭall your electric power company. Remember: electric power lines and phone lines Select your installation site with safety, as well as performance in mind. Before connecting or disconnecting a power cord, you must remove power from the power cord using a suitable service disconnect.įor safety and to achieve a good installation, please read and follow these safety precautions:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |